Switch to full style
Diskusije usko vezane uz Ubuntu i srodne distribucije (Kubuntu, Xubuntu, Lubuntu, LinuxMint...)
Odgovori

LAN problem nakon friske instalacije

17 stu 2012, 12:54

Pozdrav.

Napokon sam probao novu distribuciju.
Prvo je bio openSUSE 12.2 KDE (objasnit cu kasnije zasto nisam na njemu)
Pa sam instalirao Fedoru 17.

Naime, instalacija je prosla regularno. Bez ikakvih komplikacija.
Onda, kad sam stavio lan, nemam interneta. Normalno pokazuje da je spojen, ali kad udjem u mozillu, pokazuje error.
Namjestio sam firewall i sve, da prihvaca eth0 i wlan0.

Kad sam prije instalirao Ubuntu, normalno je radio lan.

Onda sam jucer navecer probao openSUSE i opet ovaj isti problem kao i na fedori trenutno.
Mislio sam da je neki interni problem u suseu ali ocigledno nije.


Da li ima rijesenje za ovaj problem ili da se vratim na sjebuntu?

edit: vratio sam se na ubuntu 12.10
stavio lan i opet nezeli na net.

mislim da je stvar u driverima, vjerojatno su izbrisani.
i sad, nemogu na laptop.krasno.

Re: LAN problem nakon friske instalacije

17 stu 2012, 18:16

koji error ti izbaci?

daj

ifconfig
route -n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci

pa pasteaj output ovdje

Re: LAN problem nakon friske instalacije

17 stu 2012, 18:34

Odi na Korzo, tamo imaš wlan :P ;)

AW: LAN problem nakon friske instalacije

17 stu 2012, 19:29

Vidi je li dhcpcd startan ako koristis dhcp.

Gesendet von meinem MT11i mit Tapatalk 2

Re: LAN problem nakon friske instalacije

17 stu 2012, 19:29

stefan je napisao/la:Odi na Korzo, tamo imaš wlan :P ;)


necemo se vrijeđat lol

Re: LAN problem nakon friske instalacije

17 stu 2012, 19:30

glaskoncILLa je napisao/la:koji error ti izbaci?

daj

ifconfig
route -n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci

pa pasteaj output ovdje


sad neznam dal sam trebao svaku zasebnu al evo.

Kod:
matej@matej-Aspire-7551:~$ ifconfig route-n cat/etc/resolv.conf cat /etc/network lspci
Usage:
  ifconfig [-a] [-v] [-s] <interface> [[<AF>] <address>]
  [add <address>[/<prefixlen>]]
  [del <address>[/<prefixlen>]]
  [[-]broadcast [<address>]]  [[-]pointopoint [<address>]]
  [netmask <address>]  [dstaddr <address>]  [tunnel <address>]
  [outfill <NN>] [keepalive <NN>]
  [hw <HW> <address>]  [metric <NN>]  [mtu <NN>]
  [[-]trailers]  [[-]arp]  [[-]allmulti]
  [multicast]  [[-]promisc]
  [mem_start <NN>]  [io_addr <NN>]  [irq <NN>]  [media <type>]
  [txqueuelen <NN>]
  [[-]dynamic]
  [up|down] ...

  <HW>=Hardware Type.
  List of possible hardware types:
    loop (Local Loopback) slip (Serial Line IP) cslip (VJ Serial Line IP)
    slip6 (6-bit Serial Line IP) cslip6 (VJ 6-bit Serial Line IP) adaptive (Adaptive Serial Line IP)
    strip (Metricom Starmode IP) ash (Ash) ether (Ethernet)
    ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE)
    tunnel (IPIP Tunnel) ppp (Point-to-Point Protocol) hdlc ((Cisco)-HDLC)
    lapb (LAPB) arcnet (ARCnet) dlci (Frame Relay DLCI)
    frad (Frame Relay Access Device) sit (IPv6-in-IPv4) fddi (Fiber Distributed Data Interface)
    hippi (HIPPI) irda (IrLAP) ec (Econet)
    x25 (generic X.25) eui64 (Generic EUI-64)
  <AF>=Address family. Default: inet
  List of possible address families:
    unix (UNIX Domain) inet (DARPA Internet) inet6 (IPv6)
    ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE)
    ipx (Novell IPX) ddp (Appletalk DDP) ec (Econet)
    ash (Ash) x25 (CCITT X.25)

Re: AW: LAN problem nakon friske instalacije

17 stu 2012, 19:44

Slamd64 je napisao/la:Vidi je li dhcpcd startan ako koristis dhcp.

Gesendet von meinem MT11i mit Tapatalk 2


dhcpd je serverski daemon, odnosno to imaju dhcp serveri, ne klijenti.

matej je napisao/la:
glaskoncILLa je napisao/la:koji error ti izbaci?

daj

ifconfig
route -n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci

pa pasteaj output ovdje


sad neznam dal sam trebao svaku zasebnu al evo.

Kod:
matej@matej-Aspire-7551:~$ ifconfig route-n cat/etc/resolv.conf cat /etc/network lspci
Usage:
  ifconfig [-a] [-v] [-s] <interface> [[<AF>] <address>]
  [add <address>[/<prefixlen>]]
  [del <address>[/<prefixlen>]]
  [[-]broadcast [<address>]]  [[-]pointopoint [<address>]]
  [netmask <address>]  [dstaddr <address>]  [tunnel <address>]
  [outfill <NN>] [keepalive <NN>]
  [hw <HW> <address>]  [metric <NN>]  [mtu <NN>]
  [[-]trailers]  [[-]arp]  [[-]allmulti]
  [multicast]  [[-]promisc]
  [mem_start <NN>]  [io_addr <NN>]  [irq <NN>]  [media <type>]
  [txqueuelen <NN>]
  [[-]dynamic]
  [up|down] ...

  <HW>=Hardware Type.
  List of possible hardware types:
    loop (Local Loopback) slip (Serial Line IP) cslip (VJ Serial Line IP)
    slip6 (6-bit Serial Line IP) cslip6 (VJ 6-bit Serial Line IP) adaptive (Adaptive Serial Line IP)
    strip (Metricom Starmode IP) ash (Ash) ether (Ethernet)
    ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE)
    tunnel (IPIP Tunnel) ppp (Point-to-Point Protocol) hdlc ((Cisco)-HDLC)
    lapb (LAPB) arcnet (ARCnet) dlci (Frame Relay DLCI)
    frad (Frame Relay Access Device) sit (IPv6-in-IPv4) fddi (Fiber Distributed Data Interface)
    hippi (HIPPI) irda (IrLAP) ec (Econet)
    x25 (generic X.25) eui64 (Generic EUI-64)
  <AF>=Address family. Default: inet
  List of possible address families:
    unix (UNIX Domain) inet (DARPA Internet) inet6 (IPv6)
    ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE)
    ipx (Novell IPX) ddp (Appletalk DDP) ec (Econet)
    ash (Ash) x25 (CCITT X.25)


trebao si svaku zasebno, zato sam i odvojio u posebne redove.

Re: LAN problem nakon friske instalacije

17 stu 2012, 19:53

ifconfig
Kod:
matej@matej-Aspire-7551:~$ ifconfig
eth0      Link encap:Ethernet  HWaddr 20:6a:8a:3e:9a:00 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:16

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:356 errors:0 dropped:0 overruns:0 frame:0
          TX packets:356 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:28860 (28.8 KB)  TX bytes:28860 (28.8 KB)

wlan0     Link encap:Ethernet  HWaddr 88:9f:fa:33:f3:af 
          inet addr:192.168.5.99  Bcast:192.168.5.255  Mask:255.255.255.0
          inet6 addr: fe80::8a9f:faff:fe33:f3af/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:11326 errors:0 dropped:0 overruns:0 frame:0
          TX packets:538 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:852439 (852.4 KB)  TX bytes:66823 (66.8 KB)


route-n
Kod:
matej@matej-Aspire 7551:~$ route-n
command not found


cat /etc/resolv.conf
Kod:
matej@matej-Aspire-7551:~$ cat /etc/resolv.conf
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
#     DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
nameserver 127.0.1.1
search gigaset.lan


cat /etc/network/interfaces
Kod:
matej@matej-Aspire-7551:~$ cat /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback


lspci
Kod:
matej@matej-Aspire-7551:~$ lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge
00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0)
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0)
00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1)
00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42)
00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40)
00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40)
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series]
02:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Turks/Whistler HDMI Audio [Radeon HD 6000 Series]
03:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01)
06:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01)

Re: LAN problem nakon friske instalacije

17 stu 2012, 20:09

dodaj u /etc/network/interfaces ispod svega (dakle nemoj brisati ono sto vec pise unutra)

auto eth0
iface eth0 inet dhcp

pa restartaj komp

Re: LAN problem nakon friske instalacije

17 stu 2012, 20:14

glaskoncILLa je napisao/la:dodaj u /etc/network/interfaces ispod svega (dakle nemoj brisati ono sto vec pise unutra)

auto eth0
iface eth0 inet dhcp

pa restartaj komp


could not save the file /etc/network/interfaces.
you do not have the permissions necessary to save the file. please check that you typed the location correctly and try again.
Odgovori