još ništa,
Lutherus, kad nađem vremena proučiti ću neke od ovih dokumenata koje mi predlažeš
što mislite bi li pomoglo da probam sa 32 bit 12.1
ili se prebacim na 11.4
na 11.2 wireless je radio ok
Sada je: 25 tra 2024, 20:25.
Moderator/ica: Moderatori/ce
45 post(ov)a
•
Stranica: 3/5. • 1, 2, 3, 4, 5
evo mene opet...
molio bih za pomoć:
u nastojanju za "pronalaženjem" wirelessa...
ovo sam utipkao u konzolu:
/sbin/lspci nnk
i dobio ovo:
Usage: lspci [<switches>]
Basic display modes:
-mm Produce machine-readable output (single -m for an obsolete format)
-t Show bus tree
Display options:
-v Be verbose (-vv for very verbose)
-k Show kernel drivers handling each device
-x Show hex-dump of the standard part of the config space
-xxx Show hex-dump of the whole config space (dangerous; root only)
-xxxx Show hex-dump of the 4096-byte extended config space (root only)
-b Bus-centric view (addresses and IRQ's as seen by the bus)
-D Always show domain numbers
Resolving of device ID's to names:
-n Show numeric ID's
-nn Show both textual and numeric ID's (names & numbers)
-q Query the PCI ID database for unknown ID's via DNS
-qq As above, but re-query locally cached entries
-Q Query the PCI ID database for all ID's via DNS
Selection of devices:
-s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]] Show only devices in selected slots
-d [<vendor>]:[<device>] Show only devices with specified ID's
Other options:
-i <file> Use specified ID database instead of /usr/share/pci.ids.gz
-p <file> Look up kernel modules in a given file instead of default modules.pcimap
-M Enable `bus mapping' mode (dangerous; root only)
PCI access options:
-A <method> Use the specified PCI access method (see `-A help' for a list)
-O <par>=<val> Set PCI access parameter (see `-O help' for a list)
-G Enable PCI access debugging
-H <mode> Use direct hardware access (<mode> = 1 or 2)
-F <file> Read PCI configuration dump from a given file
molio bih za pomoć:
u nastojanju za "pronalaženjem" wirelessa...
ovo sam utipkao u konzolu:
/sbin/lspci nnk
i dobio ovo:
Usage: lspci [<switches>]
Basic display modes:
-mm Produce machine-readable output (single -m for an obsolete format)
-t Show bus tree
Display options:
-v Be verbose (-vv for very verbose)
-k Show kernel drivers handling each device
-x Show hex-dump of the standard part of the config space
-xxx Show hex-dump of the whole config space (dangerous; root only)
-xxxx Show hex-dump of the 4096-byte extended config space (root only)
-b Bus-centric view (addresses and IRQ's as seen by the bus)
-D Always show domain numbers
Resolving of device ID's to names:
-n Show numeric ID's
-nn Show both textual and numeric ID's (names & numbers)
-q Query the PCI ID database for unknown ID's via DNS
-qq As above, but re-query locally cached entries
-Q Query the PCI ID database for all ID's via DNS
Selection of devices:
-s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]] Show only devices in selected slots
-d [<vendor>]:[<device>] Show only devices with specified ID's
Other options:
-i <file> Use specified ID database instead of /usr/share/pci.ids.gz
-p <file> Look up kernel modules in a given file instead of default modules.pcimap
-M Enable `bus mapping' mode (dangerous; root only)
PCI access options:
-A <method> Use the specified PCI access method (see `-A help' for a list)
-O <par>=<val> Set PCI access parameter (see `-O help' for a list)
-G Enable PCI access debugging
-H <mode> Use direct hardware access (<mode> = 1 or 2)
-F <file> Read PCI configuration dump from a given file
sa naredbom lspci ces pronaci odgovarajuce kontrolere i wireless adapter.. znaci samo l(malo L)spci upisi u konzolu i pukni enter
nakon toga daj iwconfig da vidimo jel ti vidi wlan
nakon toga daj iwconfig da vidimo jel ti vidi wlan
hvala
sutra postam nastavak jer mi je taj kući jedini comp
a ovo postam iz ureda
samo podsjećam...
na tipki kojom uključujem wireless, žaruljica koja - kad je uključena - promijeni boju u bijelu,
od kada sam instalirao 12.1. - više ne mijenja boju, stalno je žučkasta
sutra postam nastavak jer mi je taj kući jedini comp
a ovo postam iz ureda
samo podsjećam...
na tipki kojom uključujem wireless, žaruljica koja - kad je uključena - promijeni boju u bijelu,
od kada sam instalirao 12.1. - više ne mijenja boju, stalno je žučkasta
artu je napisao/la:samo podsjećam...
na tipki kojom uključujem wireless, žaruljica koja - kad je uključena - promijeni boju u bijelu,
od kada sam instalirao 12.1. - više ne mijenja boju, stalno je žučkasta
vjerojatno onda nema drivera.. al svejedno ti postaj ono pa cemo sve vidjet..
prvo sam ukucao ovo:
~> /sbin/lspci
i dobio sam ovo:
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge
00:01.0 PCI bridge: Hewlett-Packard Company Device 9602
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3)
00:09.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 4)
00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42)
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40)
00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40)
00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200]
01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200]
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
06:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
pa sam ukucao ovo:
/usr/sbin/iwconfig
i dobio ovo:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
~> /sbin/lspci
i dobio sam ovo:
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge
00:01.0 PCI bridge: Hewlett-Packard Company Device 9602
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3)
00:09.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 4)
00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42)
00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40)
00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40)
00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200]
01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200]
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)
06:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
pa sam ukucao ovo:
/usr/sbin/iwconfig
i dobio ovo:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
pa ovo sve izgleda ok!
zar nemas dole u kutu ikonu network managera i kad nju kliknes ti se izlistaju vidljive mreze.. i da.. vidi jesi li i hardverski ukljucio wireless.. preko tipke na lapu.. znam da si spominjao da nece, al probaj opet..
zar nemas dole u kutu ikonu network managera i kad nju kliknes ti se izlistaju vidljive mreze.. i da.. vidi jesi li i hardverski ukljucio wireless.. preko tipke na lapu.. znam da si spominjao da nece, al probaj opet..
probao sam klikati barem deset puta
taj lap top koristim već dvije godine i na 11.2. mi je internet radio dobro
prešao sam na 12.1 jer su druge stvari štekale
nisam više vidio yast, upgrade, itd...
dolje imam prikazane mreže, čak i svoju vidim
valjda je problem što ne mogu ukopčati wireless...
taj lap top koristim već dvije godine i na 11.2. mi je internet radio dobro
prešao sam na 12.1 jer su druge stvari štekale
nisam više vidio yast, upgrade, itd...
dolje imam prikazane mreže, čak i svoju vidim
valjda je problem što ne mogu ukopčati wireless...
artu je napisao/la:probao sam klikati barem deset puta
taj lap top koristim već dvije godine i na 11.2. mi je internet radio dobro
prešao sam na 12.1 jer su druge stvari štekale
nisam više vidio yast, upgrade, itd...
dolje imam prikazane mreže, čak i svoju vidim
valjda je problem što ne mogu ukopčati wireless...
a sto se desi kad kliknes na svoju mrezu?
mozda je problem u network manageru, pa da probamo s wicd-om..
ajde, čisto da i to probamo, u terminal kao root upiši:
pa se probaj spojit na svoju mrežu...
- Kod: Označi sve
ifup wlan0
pa se probaj spojit na svoju mrežu...
45 post(ov)a
•
Stranica: 3/5. • 1, 2, 3, 4, 5
Na mreži
Trenutno korisnika/ca: / i 8 gostiju.