minitube

/home/drago/Desktop/Screenshot.png

Do jaja..

ma čekaj htjeo sam sliku poslati,neda mi skenirati,opet se isto pojavi

ma čekaj htjeo sam sliku poslati,neda mi skenirati,opet se isto pojavi

Pa jel toliko teško staviti na pastebin.com?

pojavi se mali prozor sa znakom zabrane,neda skenirati tom programu,isto traži stalno,a piše sledeće

the file/home/drago/dowloads/speedumpmypc
(1) exe,is not marked as executable. it this was downloaded or copied from an untrusted source it may be dangerous to run. for more detalis ,read about the executable bit

stavim na postebin taj,ali neda skenirati,piše free scan,ja pokušam neda,to napise

Kod:

drago@drago-AO532h:~$ tail -n 100 /var/log/dmesg
[    2.248312] scsi2 : ahci
[    2.252244] scsi3 : ahci
[    2.253027] ata1: SATA max UDMA/133 abar m1024@0x58204000 port 0x58204100 irq 42
[    2.253040] ata2: SATA max UDMA/133 abar m1024@0x58204000 port 0x58204180 irq 42
[    2.253048] ata3: DUMMY
[    2.253054] ata4: DUMMY
[    2.350768] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.350780] i915 0000:00:02.0: setting latency timer to 64
[    2.396070] usb 1-5: new high speed USB device using ehci_hcd and address 4
[    2.419166] i915 0000:00:02.0: irq 43 for MSI/MSI-X
[    2.419178] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[    2.419183] [drm] Driver supports precise vblank timestamp query.
[    2.521033] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[    2.521414] [drm] initialized overlay support
[    2.744145] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.744897] ata1.00: unexpected _GTF length (4)
[    2.772071] usb 3-1: new low speed USB device using uhci_hcd and address 2
[    2.777228] ata1.00: ATA-8: TOSHIBA MK1655GSX, FG011J, max UDMA/100
[    2.777236] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.778014] ata1.00: unexpected _GTF length (4)
[    2.778230] ata1.00: configured for UDMA/100
[    2.778504] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK1655GS FG01 PQ: 0 ANSI: 5
[    2.779126] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.779193] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[    2.779455] sd 0:0:0:0: [sda] Write Protect is off
[    2.779467] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.779576] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.863514]  sda: sda1 sda2 < sda5 >
[    2.864512] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.918088] fbcon: inteldrmfb (fb0) is primary device
[    2.918236] Console: switching to colour frame buffer device 128x37
[    2.918308] fb0: inteldrmfb frame buffer device
[    2.918314] drm: registered panic notifier
[    3.096151] ata2: SATA link down (SStatus 0 SControl 300)
[    3.136969] input: Genius Optical Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input5
[    3.137411] generic-usb 0003:0458:003A.0001: input,hidraw0: USB HID v1.11 Mouse [Genius Optical Mouse] on usb-0000:00:1d.1-1/input0
[    3.137475] usbcore: registered new interface driver usbhid
[    3.137483] usbhid: USB HID core driver
[    3.228201] acpi device:28: registered as cooling_device3
[    3.228789] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input6
[    3.228960] ACPI: Video Device [OVGA] (multi-head: yes  rom: no  post: no)
[    3.229285] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[    3.728182] fixme: max PWM is zero.
[    5.945217] Btrfs loaded
[    5.958796] xor: automatically using best checksumming function: pIII_sse
[    5.976030]    pIII_sse  :  5059.000 MB/sec
[    5.976040] xor: using function: pIII_sse (5059.000 MB/sec)
[    5.984561] device-mapper: dm-raid45: initialized v0.2594b
[    6.321112] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[   18.727822] <30>udev[330]: starting version 167
[   18.749312] Adding 1036284k swap on /dev/sda5.  Priority:-1 extents:1 across:1036284k
[   18.815703] lp: driver loaded but no devices found
[   19.042454] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[   19.425621] type=1400 audit(1331241291.233:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=526 comm="apparmor_parser"
[   19.432379] type=1400 audit(1331241291.241:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=526 comm="apparmor_parser"
[   19.433107] type=1400 audit(1331241291.241:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=526 comm="apparmor_parser"
[   20.158058] keucr: module is from the staging directory, the quality is unknown, you have been warned.
[   20.296180] atl1c 0000:01:00.0: irq 44 for MSI/MSI-X
[   20.296308] atl1c 0000:01:00.0: atl1c: eth0 NIC Link is Up<100 Mbps Full Duplex>
[   20.526936] usb --- usb_stor_init start
[   20.526991] usb --- eucr_probe
[   20.546852] cfg80211: Calling CRDA to update world regulatory domain
[   20.549898] usb --- associate_dev
[   20.549921] usb --- get_device_info
[   20.549927] usb --- get_transport
[   20.549931] usb --- get_protocol
[   20.549937] us->pusb_dev->descriptor.idVendor = cf2
[   20.549943] us->pusb_dev->descriptor.idProduct = 6250
[   20.549948] usb --- get_pipes
[   20.549953] usb --- usb_stor_acquire_resources
[   20.566602] scsi4 : SCSI emulation for USB Mass Storage devices
[   20.566849] usb --- usb_stor_control_thread
[   20.574232] usbcore: registered new interface driver eucr
[   20.574243] ENE USB Mass Storage support registered.
[   20.574531] usb --- usb_stor_scan_thread
[   20.574541] EUCR : device found at 4
[   20.792382] Linux video capture interface: v2.00
[   21.007678] type=1400 audit(1331241292.813:5): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=792 comm="apparmor_parser"
[   21.014695] type=1400 audit(1331241292.821:6): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=793 comm="apparmor_parser"
[   21.015819] type=1400 audit(1331241292.821:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=793 comm="apparmor_parser"
[   21.031946] type=1400 audit(1331241292.837:8): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=793 comm="apparmor_parser"
[   21.078829] type=1400 audit(1331241292.885:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=796 comm="apparmor_parser"
[   21.081640] type=1400 audit(1331241292.889:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=796 comm="apparmor_parser"
[   21.111723] type=1400 audit(1331241292.917:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=797 comm="apparmor_parser"
[   21.363785] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa40000/0xa0000
[   21.431609] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[   21.581345] EUCR : device scan complete
[   21.581534] scsi cmd 12 --- SCSIOP_INQUIRY
[   21.581542] --- Init Media ---
[   21.582364] MiscReg03 = 1
[   21.582372] transport --- ENE_SDInit
[   21.582379] SD_INIT1_PATTERN
[   21.659877] zram: module is from the staging directory, the quality is unknown, you have been warned.
[   21.680802] uvcvideo: Found UVC 1.00 device Webcam (04f2:b19d)
[   21.703477] zram: Creating 2 devices ...
[   21.720482] input: Webcam as /devices/pci0000:00/0000:00:1d.7/usb1/1-4/1-4:1.0/input/input8
[   21.785775] usbcore: registered new interface driver uvcvideo
[   21.785785] USB Video Class driver (v1.0.0)
[   21.806262] Adding 507224k swap on /dev/zram0.  Priority:100 extents:1 across:507224k SS
[   21.821267] Adding 507224k swap on /dev/zram1.  Priority:100 extents:1 across:507224k SS
drago@drago-AO532h:~$

ADMIN: Ubuduće staviti u "Code" tag ispise ove dužine.

to mi je terminal izbacio ali neznam sa tim šta,stavim tamo u taj postebin.ali neće skenirati,ili neznam šta drugo da uradim

izgleda da sam uspio sve rastjerati,ha,ha. ma neradi kako treba i to je to,jedino do sada što vrti je ubuntu i mint gnome,ostalo sve da glava boli,tako sad i ovaj zorin,mandrivu i opensuse i ostale neću ni probavati da ne bacam komp kroz prozor,ha,ha. nemam nikoga blizui da mi pokaže kako se sve radi,a ovako preko neta,mislim da je samo muka.

/home/drago/Desktop/Screenshot.png

Do jaja..

pojavi se mali prozor sa znakom zabrane,neda skenirati tom programu,isto traži stalno,a piše sledeće

the file/home/drago/dowloads/speedumpmypc
(1) exe,is not marked as executable. it this was downloaded or copied from an untrusted source it may be dangerous to run. for more detalis ,read about the executable bit

Evo čitam i smijem se svemu pomalo. Nisi ti kriv, drago.. počeci su teški. Zaboravi na .exe datoteke, one su namjenjene windowsima, a ne linuxu. Inače, ako imaš instaliran wine (a mislim da sa ZorinOS-om dolazi po difoltu), neke .exe datoteke možeš pokrenut. U ovom slučaju, koji si naveo u gornjem citatu, klikni desni klik na speedumpmypc.exe (iako po imenu datoteke ne vidim zašto bi ti to trebalo na linuxu), odi na Svojstva (Propreties), pa na tab Dozvole (Permissions) i označi kvačicu di piše nešto tipa "Allow executing as program". Sada možeš pokušat pokrenut taj .exe koji ti, iskreno, nema što ni tražit, a ni radit na linuxu. Za Debian i na njemu bazirane sustave (Ubuntu, ZorinOs, SuperOS...) koriste se .deb paketi.