Linux za Sve forum

Kod: Označi sve

[vlado@archlinux ~]$ hwinfo --disk
26: SCSI 200.0: 10600 Disk                                     
  [Created at block.256]
  Unique ID: uI_Q.ZiH4cwUk08E
  Parent ID: 06bT.ZbgJ97dQy94
  SysFS ID: /class/block/sdb
  SysFS BusID: 2:0:0:0
  SysFS Device Link: /devices/pci0000:00/0000:00:13.2/usb2/2-2/2-2:1.0/host2/target2:0:0/2:0:0:0
  Hardware Class: disk
  Model: "Generic Multi-Card"
  Vendor: "Generic-"
  Device: "Multi-Card"
  Revision: "1.00"
  Driver: "ums-realtek", "sd"
  Driver Modules: "ums_realtek", "sd_mod"
  Device File: /dev/sdb
  Device Files: /dev/sdb, /dev/disk/by-path/pci-0000:00:13.2-usb-0:2:1.0-scsi-0:0:0:0, /dev/disk/by-id/usb-Generic-_Multi-Card_20090516388200000-0:0
  Device Number: block 8:16-8:31
  Drive status: no medium
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #3 (USB Controller)


Kod: Označi sve

[vlado@archlinux ~]$ sudo badblocks -sv /dev/sda
[sudo] password for vlado:
Checking blocks 0 to 312571223
Checking for bad blocks (read-only test): done                                                 
Pass completed, 0 bad blocks found. (0/0/0 errors)


Vl@do je napisao/la:...
Po ovome ispada ja je sve u redu?...

shrike je napisao/la:što je output od smartctl?

Kod: Označi sve

[vlado@archlinux ~]$ sudo smartctl -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.20.0-arch1-1-ARCH] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Toshiba 2.5" HDD MK..59GSXP (AF)
Device Model:     TOSHIBA MK3259GSX
Serial Number:    X0KVB1JAB
LU WWN Device Id: 5 000039 2da0858fc
Firmware Version: GK003U
User Capacity:    320,072,933,376 bytes [320 GB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS (minor revision not indicated)
SATA Version is:  SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s)
Local Time is:    Fri Jan 18 16:13:22 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)   Offline data collection activity
               was never started.
               Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)   The previous self-test routine completed
               without error or no self-test has ever
               been run.
Total time to complete Offline
data collection:       (  120) seconds.
Offline data collection
capabilities:           (0x5b) SMART execute Offline immediate.
               Auto Offline data collection on/off support.
               Suspend Offline collection upon new
               command.
               Offline surface scan supported.
               Self-test supported.
               No Conveyance Self-test supported.
               Selective Self-test supported.
SMART capabilities:            (0x0003)   Saves SMART data before entering
               power-saving mode.
               Supports SMART auto save timer.
Error logging capability:        (0x01)   Error logging supported.
               General Purpose Logging supported.
Short self-test routine
recommended polling time:     (   2) minutes.
Extended self-test routine
recommended polling time:     (  99) minutes.
SCT capabilities:           (0x003d)   SCT Status supported.
               SCT Error Recovery Control supported.
               SCT Feature Control supported.
               SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   050    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0027   100   100   001    Pre-fail  Always       -       1702
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       697
  5 Reallocated_Sector_Ct   0x0033   100   100   050    Pre-fail  Always       -       24
  7 Seek_Error_Rate         0x000b   100   100   050    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0032   098   098   000    Old_age   Always       -       994
 10 Spin_Retry_Count        0x0033   113   100   030    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       661
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       2
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       100
193 Load_Cycle_Count        0x0032   098   098   000    Old_age   Always       -       25832
194 Temperature_Celsius     0x0022   100   100   000    Old_age   Always       -       26 (Min/Max 9/53)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       2
197 Current_Pending_Sector  0x0032   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0030   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
220 Disk_Shift              0x0002   100   100   000    Old_age   Always       -       53
222 Loaded_Hours            0x0032   099   099   000    Old_age   Always       -       437
223 Load_Retry_Count        0x0032   100   100   000    Old_age   Always       -       0
224 Load_Friction           0x0022   100   100   000    Old_age   Always       -       0
226 Load-in_Time            0x0026   100   100   000    Old_age   Always       -       313
240 Head_Flying_Hours       0x0001   100   100   001    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
   CR = Command Register [HEX]
   FR = Features Register [HEX]
   SC = Sector Count Register [HEX]
   SN = Sector Number Register [HEX]
   CL = Cylinder Low Register [HEX]
   CH = Cylinder High Register [HEX]
   DH = Device/Head Register [HEX]
   DC = Device Command Register [HEX]
   ER = Error register [HEX]
   ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 12 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 07 40 00 5e 40  Error: UNC 7 sectors at LBA = 0x005e0040 = 6160448

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 03 08 3f 00 5e 40 00      00:00:45.347  READ DMA EXT
  25 03 08 27 02 5e 40 00      00:00:45.347  READ DMA EXT
  25 03 08 1f 02 5e 40 00      00:00:45.346  READ DMA EXT
  25 03 08 17 02 5e 40 00      00:00:45.346  READ DMA EXT
  25 03 08 0f 02 5e 40 00      00:00:45.345  READ DMA EXT

Error 11 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 4f 00 5e 40  Error: UNC 8 sectors at LBA = 0x005e004f = 6160463

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 03 08 4f 00 5e 40 00      00:00:41.372  READ DMA EXT
  25 03 08 47 00 5e 40 00      00:00:37.438  READ DMA EXT
  25 03 08 3f 00 5e 40 00      00:00:33.416  READ DMA EXT
  35 03 08 37 00 5e 40 00      00:00:33.415  WRITE DMA EXT
  35 03 08 2f 00 5e 40 00      00:00:33.414  WRITE DMA EXT

Error 10 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 47 00 5e 40  Error: UNC 8 sectors at LBA = 0x005e0047 = 6160455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 03 08 47 00 5e 40 00      00:00:37.438  READ DMA EXT
  25 03 08 3f 00 5e 40 00      00:00:33.416  READ DMA EXT
  35 03 08 37 00 5e 40 00      00:00:33.415  WRITE DMA EXT
  35 03 08 2f 00 5e 40 00      00:00:33.414  WRITE DMA EXT
  25 03 08 27 00 60 40 00      00:00:33.362  READ DMA EXT

Error 9 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 07 40 00 5e 40  Error: UNC 7 sectors at LBA = 0x005e0040 = 6160448

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 03 08 3f 00 5e 40 00      00:00:33.416  READ DMA EXT
  35 03 08 37 00 5e 40 00      00:00:33.415  WRITE DMA EXT
  35 03 08 2f 00 5e 40 00      00:00:33.414  WRITE DMA EXT
  25 03 08 27 00 60 40 00      00:00:33.362  READ DMA EXT
  35 03 08 3f 00 60 40 00      00:00:33.361  WRITE DMA EXT

Error 8 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 4f 00 5e 40  Error: UNC 8 sectors at LBA = 0x005e004f = 6160463

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 03 08 4f 00 5e 40 00      00:00:29.336  READ DMA EXT
  25 03 08 27 00 60 40 00      00:00:29.329  READ DMA EXT
  25 03 08 57 00 5e 40 00      00:00:29.316  READ DMA EXT
  25 03 08 4f 00 5e 40 00      00:00:25.371  READ DMA EXT
  25 03 08 4f 00 5e 40 00      00:00:21.360  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%       992         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.