Stranica: 1/1.
HDD usporava
Postano: 17 sij 2019, 18:08
Postao/la Vl@do
Neke aplikacije otvara cca 7-8 sec. Ranije je to bilo puno brže.
Google Chrome otvara za 6 sec, ali potpuno otvaranje stranice nekih novina čekam i do 15 sec. O više tabova da ne govorim. Ranije je to bilo puno brže.
Predpostavljam da se radi o HDD-u koji je pretrpio svašta u toku mog "školovanja". Jedan HDD sam sahranio već, a ovo je isto neki polovni ugrađen prije nekih godinu dana.
Acer Aspire 5250
Kod: Označi sve
[vlado@archlinux ~]$ hwinfo --disk
26: SCSI 200.0: 10600 Disk
[Created at block.256]
Unique ID: uI_Q.ZiH4cwUk08E
Parent ID: 06bT.ZbgJ97dQy94
SysFS ID: /class/block/sdb
SysFS BusID: 2:0:0:0
SysFS Device Link: /devices/pci0000:00/0000:00:13.2/usb2/2-2/2-2:1.0/host2/target2:0:0/2:0:0:0
Hardware Class: disk
Model: "Generic Multi-Card"
Vendor: "Generic-"
Device: "Multi-Card"
Revision: "1.00"
Driver: "ums-realtek", "sd"
Driver Modules: "ums_realtek", "sd_mod"
Device File: /dev/sdb
Device Files: /dev/sdb, /dev/disk/by-path/pci-0000:00:13.2-usb-0:2:1.0-scsi-0:0:0:0, /dev/disk/by-id/usb-Generic-_Multi-Card_20090516388200000-0:0
Device Number: block 8:16-8:31
Drive status: no medium
Config Status: cfg=new, avail=yes, need=no, active=unknown
Attached to: #3 (USB Controller)
Po ovome ispada ja je sve u redu?
Kod: Označi sve
[vlado@archlinux ~]$ sudo badblocks -sv /dev/sda
[sudo] password for vlado:
Checking blocks 0 to 312571223
Checking for bad blocks (read-only test): done
Pass completed, 0 bad blocks found. (0/0/0 errors)
Re: HDD usporava
Postano: 17 sij 2019, 20:38
Postao/la shrike
što je output od smartctl?
Re: HDD usporava
Postano: 17 sij 2019, 22:05
Postao/la bertone
Vl@do je napisao/la:...
Po ovome ispada ja je sve u redu?...
Znači ipak je do Archa
Re: HDD usporava
Postano: 18 sij 2019, 16:16
Postao/la Vl@do
shrike je napisao/la:što je output od smartctl?
Kod: Označi sve
[vlado@archlinux ~]$ sudo smartctl -a /dev/sda
smartctl 7.0 2018-12-30 r4883 [x86_64-linux-4.20.0-arch1-1-ARCH] (local build)
Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MK..59GSXP (AF)
Device Model: TOSHIBA MK3259GSX
Serial Number: X0KVB1JAB
LU WWN Device Id: 5 000039 2da0858fc
Firmware Version: GK003U
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s)
Local Time is: Fri Jan 18 16:13:22 2019 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 99) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1702
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 697
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 24
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 994
10 Spin_Retry_Count 0x0033 113 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 661
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 2
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 100
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 25832
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 26 (Min/Max 9/53)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 2
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 53
222 Loaded_Hours 0x0032 099 099 000 Old_age Always - 437
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 313
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 12 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 12 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 07 40 00 5e 40 Error: UNC 7 sectors at LBA = 0x005e0040 = 6160448
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 3f 00 5e 40 00 00:00:45.347 READ DMA EXT
25 03 08 27 02 5e 40 00 00:00:45.347 READ DMA EXT
25 03 08 1f 02 5e 40 00 00:00:45.346 READ DMA EXT
25 03 08 17 02 5e 40 00 00:00:45.346 READ DMA EXT
25 03 08 0f 02 5e 40 00 00:00:45.345 READ DMA EXT
Error 11 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 4f 00 5e 40 Error: UNC 8 sectors at LBA = 0x005e004f = 6160463
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 4f 00 5e 40 00 00:00:41.372 READ DMA EXT
25 03 08 47 00 5e 40 00 00:00:37.438 READ DMA EXT
25 03 08 3f 00 5e 40 00 00:00:33.416 READ DMA EXT
35 03 08 37 00 5e 40 00 00:00:33.415 WRITE DMA EXT
35 03 08 2f 00 5e 40 00 00:00:33.414 WRITE DMA EXT
Error 10 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 47 00 5e 40 Error: UNC 8 sectors at LBA = 0x005e0047 = 6160455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 47 00 5e 40 00 00:00:37.438 READ DMA EXT
25 03 08 3f 00 5e 40 00 00:00:33.416 READ DMA EXT
35 03 08 37 00 5e 40 00 00:00:33.415 WRITE DMA EXT
35 03 08 2f 00 5e 40 00 00:00:33.414 WRITE DMA EXT
25 03 08 27 00 60 40 00 00:00:33.362 READ DMA EXT
Error 9 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 07 40 00 5e 40 Error: UNC 7 sectors at LBA = 0x005e0040 = 6160448
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 3f 00 5e 40 00 00:00:33.416 READ DMA EXT
35 03 08 37 00 5e 40 00 00:00:33.415 WRITE DMA EXT
35 03 08 2f 00 5e 40 00 00:00:33.414 WRITE DMA EXT
25 03 08 27 00 60 40 00 00:00:33.362 READ DMA EXT
35 03 08 3f 00 60 40 00 00:00:33.361 WRITE DMA EXT
Error 8 occurred at disk power-on lifetime: 510 hours (21 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 4f 00 5e 40 Error: UNC 8 sectors at LBA = 0x005e004f = 6160463
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 03 08 4f 00 5e 40 00 00:00:29.336 READ DMA EXT
25 03 08 27 00 60 40 00 00:00:29.329 READ DMA EXT
25 03 08 57 00 5e 40 00 00:00:29.316 READ DMA EXT
25 03 08 4f 00 5e 40 00 00:00:25.371 READ DMA EXT
25 03 08 4f 00 5e 40 00 00:00:21.360 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 992 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.