Stranica: 1/2.
pci problem
Postano: 14 pro 2012, 20:04
Postao/la omelo
ovo sam pitanje postavljao na vise foruma ijos nisam dobio odgovor, naime radi se o pci serial pport kartici koju imam i nikako da je prepozna. rec je o ubuntu serveru 12.04 i nekoj kineskoj karici sa 2 s i 1 p portom, za koje ima i driveri ali nikako da je pokrenem inace jedva sam nekako po uputstvu ubacio driver u folder ali nista evo u prilogu saljem sve.
Re: pci problem
Postano: 14 pro 2012, 22:11
Postao/la max360se
daj lspci
Re: pci problem
Postano: 15 pro 2012, 10:17
Postao/la omelo
Re: pci problem
Postano: 15 pro 2012, 15:07
Postao/la max360se
Ovo su uputstva koje si dao, jesi li napravio sve korake?
Kod: Označi sve
(1)-install
<1>-copy ch35x_80x86.o to /usr/sbin
<2>-Add /usr/sbin/ch35x_80x86 at the end of the /etc/rc.d/rc.local.
<3>-reboot
if you inster two serials port board
The ttyS2 and ttyS3 are ready for application.
if you inster one serial port and one parport port board
The ttyS2 and LPT1 or LPT2 ready for application.
if you inster four serials port board
The ttyS2 ttyS3 ttyS4 and ttyS5 are ready for application.
if you inster two serials port and aone parport port board
The ttyS2 ttyS3 and LPT1 or LPT2 are ready for application.
Trebalo bi raditi, a i izgleda da vidi serijalce
daj još
dmesg | tail
Re: pci problem
Postano: 15 pro 2012, 15:22
Postao/la omelo
[ 15.604885] codec_read: codec 0 is not valid [0x107e5370]
[ 15.613194] codec_read: codec 0 is not valid [0x107e5370]
[ 15.621478] codec_read: codec 0 is not valid [0x107e5370]
[ 18.047379] init: failsafe main process (794) killed by TERM signal
[ 18.258025] type=1400 audit(1355581224.726:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=863 comm="apparmor_parser"
[ 18.259952] type=1400 audit(1355581224.726:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=863 comm="apparmor_parser"
[ 18.267237] type=1400 audit(1355581224.734:10): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=865 comm="apparmor_parser"
[ 18.270953] type=1400 audit(1355581224.738:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=863 comm="apparmor_parser"
[ 18.869699] init: plymouth-upstart-bridge main process (828) killed by TERM signal
[ 24.544014] eth0: no IPv6 routers present
Re: pci problem
Postano: 15 pro 2012, 15:33
Postao/la omelo
to je usr/sbin i atr su 755
Re: pci problem
Postano: 15 pro 2012, 15:35
Postao/la omelo
a ovo je u etc/rc.local po uputstvu bi ovo trebalo biti sve ali .....
#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.
/usr/local/bin/oscam -b -c /usr/local/etc/&
/usr/local/bin/CCcam.x86
/usr/sbin/ch35x_80x86
exit= 0
Re: pci problem
Postano: 15 pro 2012, 15:39
Postao/la omelo
ili mozda trebam napraviti ovo: /etc/rc.d/rc.local pa u njega ubaciti script, ali mislim da je to proslost i da na novijim verzijama vise nema /etc/rc.d/rc.local nego samo etc/rc.local
Re: pci problem
Postano: 15 pro 2012, 15:41
Postao/la max360se
Stavi da je root owner. Uff dalje od ovog nisam siguran kako dalje.
Re: pci problem
Postano: 15 pro 2012, 15:52
Postao/la omelo
mozda je to, nisam ni primetio ali kako da promenim to u root???