pppoe over wifi

[zole052]

sjetio se starog problema kod linuxa...jel netko zna jel postoji neko rjesenje za ovo? jel mozda suse to ubacio u yast? control centar u pclosu?

[scheissman]

a koji je bio prblem ? preko kabla je radio a preko wifi -a ne ?
ovako nesto ili idem krivim putem ? https://bbs.archlinux.org/viewtopic.php?id=52025

[zole052]

a koji je bio prblem ? preko kabla je radio a preko wifi -a ne ?

ma preko kabla radi ali trebalo bi napraviti pppoe konekciju preko wifi-ja a za to nema nacina (nije bilo)

osim da se spojis na wireles pa onda napravis pppoeconf i namjestis sve ali onda nakon restarta vise neradi i nemozes se opet uopce spojiti, isprobano prije nesto manje od godine dana

[scheissman]

a koji je bio prblem ? preko kabla je radio a preko wifi -a ne ?

ma preko kabla radi ali trebalo bi napraviti pppoe konekciju preko wifi-ja a za to nema nacina (nije bilo)

osim da se spojis na wireles pa onda napravis pppoeconf i namjestis sve ali onda nakon restarta vise neradi i nemozes se opet uopce spojiti, isprobano prije nesto manje od godine dana

neznam jesi skonto gore post. sa arch foruma ?

[zole052]

neznam jesi skonto gore post. sa arch foruma ?

sada vidim ali posten da budem ne razumim

[simke]

ja to radom ovako.
konfiguriras pppoe sa (pppoe ili rp-pppoe paket)

Kod: Označi sve

sudo pppoe-setup

napravis skriptu /etc/ppp/ip-pre-up

Kod: Označi sve

#!/bin/sh
/sbin/route del default

i chmod-as je da je može izvšavat. i onda

Kod: Označi sve

pppoe-start

naravno, spojen na wlan prije pppoe-start.

[zole052]

ja to radom ovako.
konfiguriras pppoe sa (pppoe ili rp-pppoe paket)

Kod: Označi sve

sudo pppoe-setup

napravis skriptu /etc/ppp/ip-pre-up

Kod: Označi sve

#!/bin/sh
/sbin/route del default

i chmod-as je da je može izvšavat. i onda

Kod: Označi sve

pppoe-start

naravno, spojen na wlan prije pppoe-start.

tako jednostavno... ali evo par glupih pitanja

-znaci skripta se jednostavno zove ip-pre-up a ne recimo ip-pre-up.sh ili nesto drgo?

-kako se ta skripta uopce pokrece ako je jedino sto radis da pokrenes pppoe-start nakon sto iskonfiguriras pppoe i napravis skriptu?

[simke]

sve sam ti napisao, da zove se samo ip-pre-up i nepokreces je ti, samo je napiši i

Kod: Označi sve

chmod +x /etc/ppp/ip-pre-up

i kad pozoveš pppoe-setup ljepo te pita sve podatek,i me, pass, vajrles, fajrvol. i to je to.

[zole052]

kada sam ukucao pppoe-setup izbacilo mi da nema neki konfiguracijski file da ga treba kreirati... ode na google kaze da ga kreiram sa pppoeconf i to napravim, spojen na wireles i lijepo pokrene konekciju i radi pppoe over wifi

resetiram komp i pri pokretanje os-a izbaci gresku "waiting for network konfiguration..." i tu stoji i stoji... sa esc preskocim to i udje mi u mint u kojem vise ne postoji wifi...

bootam live cd, brisem skriptu resetiram i opet ista stvar... ode mint u pm... evo me na windozama

[simke]

kada sam ukucao pppoe-setup izbacilo mi da nema neki konfiguracijski file da ga treba kreirati... ode na google kaze da ga kreiram sa pppoeconf i to napravim, spojen na wireles i lijepo pokrene konekciju i radi pppoe over wifi

resetiram komp i pri pokretanje os-a izbaci gresku "waiting for network konfiguration..." i tu stoji i stoji... sa esc preskocim to i udje mi u mint u kojem vise ne postoji wifi...

bootam live cd, brisem skriptu resetiram i opet ista stvar... ode mint u pm... evo me na windozama

sad pitaj gug'l šta dalje, ja sam ti reko kako se to najjednostavnije radi.
a za faj si mogo pitat, evo ti ga svejedno.

Kod: Označi sve

#***********************************************************************
#
# pppoe.conf
#
# Configuration file for rp-pppoe.  Edit as appropriate and install in
# /etc/ppp/pppoe.conf
#
# NOTE: This file is used by the pppoe-start, pppoe-stop, pppoe-connect and
#       pppoe-status shell scripts.  It is *not* used in any way by the
#       "pppoe" executable.
#
# Copyright (C) 2000 Roaring Penguin Software Inc.
#
# This file may be distributed under the terms of the GNU General
# Public License.
#
# LIC: GPL
# $Id$
#***********************************************************************

# When you configure a variable, DO NOT leave spaces around the "=" sign.

# Ethernet card connected to DSL modem
ETH=eth1

# PPPoE user name.  You may have to supply "@provider.com"  Sympatico
# users in Canada do need to include "@sympatico.ca"
# Sympatico uses PAP authentication.  Make sure /etc/ppp/pap-secrets
# contains the right username/password combination.
# For Magma, use xxyyzz@magma.ca
USER=bxxxnxnx@sympatico.ca

# Bring link up on demand?  Default is to leave link up all the time.
# If you want the link to come up on demand, set DEMAND to a number indicating
# the idle time after which the link is brought down.
DEMAND=no
#DEMAND=300

# DNS type: SERVER=obtain from server; SPECIFY=use DNS1 and DNS2;
# NOCHANGE=do not adjust.
DNSTYPE=SERVER

# Obtain DNS server addresses from the peer (recent versions of pppd only)
# In old config files, this used to be called USEPEERDNS.  Changed to
# PEERDNS for better Red Hat compatibility
PEERDNS=yes

DNS1=
DNS2=

# Make the PPPoE connection your default route.  Set to
# DEFAULTROUTE=no if you don't want this.
DEFAULTROUTE=yes

### ONLY TOUCH THE FOLLOWING SETTINGS IF YOU'RE AN EXPERT

# How long pppoe-start waits for a new PPP interface to appear before
# concluding something went wrong.  If you use 0, then pppoe-start
# exits immediately with a successful status and does not wait for the
# link to come up.  Time is in seconds.
#
# WARNING WARNING WARNING:
#
# If you are using rp-pppoe on a physically-inaccessible host, set
# CONNECT_TIMEOUT to 0.  This makes SURE that the machine keeps trying
# to connect forever after pppoe-start is called.  Otherwise, it will
# give out after CONNECT_TIMEOUT seconds and will not attempt to
# connect again, making it impossible to reach.
CONNECT_TIMEOUT=30

# How often in seconds pppoe-start polls to check if link is up
CONNECT_POLL=2

# Specific desired AC Name
ACNAME=

# Specific desired service name
SERVICENAME=

# Character to echo at each poll.  Use PING="" if you don't want
# anything echoed
PING="."

# File where the pppoe-connect script writes its process-ID.
# Three files are actually used:
#   $PIDFILE       contains PID of pppoe-connect script
#   $PIDFILE.pppoe contains PID of pppoe process
#   $PIDFILE.pppd  contains PID of pppd process
CF_BASE=`basename $CONFIG`
PIDFILE="/var/run/$CF_BASE-pppoe.pid"

# Do you want to use synchronous PPP?  "yes" or "no".  "yes" is much
# easier on CPU usage, but may not work for you.  It is safer to use
# "no", but you may want to experiment with "yes".  "yes" is generally
# safe on Linux machines with the n_hdlc line discipline; unsafe on others.
SYNCHRONOUS=no

# Do you want to clamp the MSS?  Here's how to decide:
# - If you have only a SINGLE computer connected to the DSL modem, choose
#   "no".
# - If you have a computer acting as a gateway for a LAN, choose "1412".
#   The setting of 1412 is safe for either setup, but uses slightly more
#   CPU power.
CLAMPMSS=1412
#CLAMPMSS=no

# LCP echo interval and failure count.
LCP_INTERVAL=20
LCP_FAILURE=3

# PPPOE_TIMEOUT should be about 4*LCP_INTERVAL
PPPOE_TIMEOUT=80

# Firewalling: One of NONE, STANDALONE or MASQUERADE
FIREWALL=NONE

# Linux kernel-mode plugin for pppd.  If you want to try the kernel-mode
# plugin, use LINUX_PLUGIN=/etc/ppp/plugins/rp-pppoe.so
LINUX_PLUGIN=

# Any extra arguments to pass to pppoe.  Normally, use a blank string
# like this:
PPPOE_EXTRA=""

# Rumour has it that "Citizen's Communications" with a 3Com
# HomeConnect DSL Modem DualLink requires these extra options:
# PPPOE_EXTRA="-f 3c12:3c13 -S ISP"

# Any extra arguments to pass to pppd.  Normally, use a blank string
# like this:
PPPD_EXTRA=""


########## DON'T CHANGE BELOW UNLESS YOU KNOW WHAT YOU ARE DOING
# If you wish to COMPLETELY overrride the pppd invocation:
# Example:
# OVERRIDE_PPPD_COMMAND="pppd call dsl"

# If you want pppoe-connect to exit when connection drops:
# RETRY_ON_FAILURE=no